Fully automatic floor scrubber is a hand push, Auto moving or Ride on floor cleaning machine. With front brush cleaning set and behind suction dryer set .
By one or more mechanical rotary brushes and solvents to clean floor.
Within a solution tank for solvent, the concentration of solvent should according to the degree of fouling cleaning objects and machine models.
The brush should with solvent when machine moving ahead, through the mechanical rotation of brush can completely scrub the ground. Meanwhile,
The back squeegee set through the suction system make the outflow of washing liquid along with the dust together into the recovery tank.
Please use warm water or Water at room temperature to clean, do not above 50℃.
There are two main types : walk behind floor scrubber, manual push to walk. Ride on floor scrubber, for more bigger areas. In addition, there are some floor scrubber with driving motor.
The flowing show the advantages of two main types.
1)Walk behind type
working size from 35cm-100cm;
24V/36V battery;
manual push or with a driving motor;
Independent water tank, with filmy or segregated filter(the latter is few).
With 1-3pcs brushes or pad drivers.
2)Ride on type
working width from 65cm-150cm;
24/36V battery ,diesel, oil fuel;
with electric driving motor
Independent water tank, with filmy and segregated filter or water cleaning cycle system(the latter two are few).
With 1-3pcs brushes or pad drivers
The machine with powerful cleaning efficiency, is widely used in indoors, Various types of all kinds of dirt grounds outdoors
Tile floor
Marble floor
Concrete floor
Asphalt felt surface
Connection seam place
Ceramic floor
If the machine need to work every day, you'd better buy good one. Or reduce the working time. If floor is hard to clean, especially workshop dust, sludge, Industrial residue dye, etc. Advise u to use special equipments: Change of polyamide fiber brush, floor brush sets, columnar cleaning brush or special squeegee.
Nowadays, fully automatic floor scrubber is very important in floor machines: Applied to various occasions, public and private environments; industry , communities and schools, office buildings, religious buildings, hospitals and public facilities, airports, ports, shopping mall, logistics center; Cleaning company and various kinds of services companies
Structures
1)Cleaning unit: with brush motor and rolling pad driver, cleaning effect depends on the size of the moving orbit.
2)Tanks: Usually have 2, one for clean water, another for sewage. Tanks' carrying capacity directly affects the machine independent performance and consumption rate
3)Dust collection unit: Equipped with suction steak and on this basis, determines the shape of the dust collection unit, equipped with suction pump at the same time. Pump absorption will affect the performance of the machine work and quality.
4)Power supply types: usually use 24/36v battery, or 220-230v electric fuel.For machines's better independent operation, performance, longer lifetime you should maintain it well.
Due to machine parts is customized according to users –specially designed for users's different problems, for ensure that the machine is in good running condition , so it is particularly important.
Users can buy the common parts from market:
1) Different kinds of cleaning brush, nylon system with different size, polyamide fiber, natural fiber, steel, The cleaning brush according to the ground and fouling of different disk and column.
2)Cylindrical brush and holder, as the optional cleaning brush, can according to the situation on the ground, change the hardness and strength of grinding.
3)Suction plate rubber, can choose different hardness according to ground conditions.
4) Replaceable scrubbing and cleaning unit
5)Water cleaning circulation system, can through the filter system for water reuse(very few).
6)At night or dark environment using machine headlamps.
Here is the main brush types and functions:
1)Applicable to all types of floor, it is Wear-resistant and high temperature resistance (hot water can 't more than 60 degrees) Due to PPL does not absorb moisture so work on the wet floor can keep its characteristics.
2)Nylon brush
Applicable to all types of floor, it is Wear-resistant and high temperature resistance (hot water can 't more than 60 degrees) Due to nylon brush the moisture absorption and easy extension so if work on the wet floor can not keep its characteristics
3)Wear-resistant hard brush
The brush bristles are very hard, and are suitable for the special dirty floor. We recommend that you use the minimum pressure to prevent damage the floor.
4)Steel brush
Steel brush, which is made from steel wire and artificial fiber. Steel brush used to clean the extremely uneven ground or big interface, gaps, And to deal with extremely difficult to remove dirt.
5)Artificial fiber brush
Brush made of plant fiber ,especially suitable for fine and non abrasion resistant thin floor.
This cleaning brush wear faster than nylon brush, to cope with the use of non corrosive liquid detergent.
6)Dense hard brush
The brush bristles is dense, hard and straight, Suitable for combination of sewing narrow smooth ceramic tile floor
We recommend that in the rough or deep seam or corner floor using a soft brush, In order to obtain a good cleaning effect
Please note that the ideal cleaning effect can not be achieved when the brush is worn out or too short.
If the brush is too long, it is easy to shaking
7)Clamping type floor polishing brush
Clamping type floor polishing brush for cleaning and polishing floor surface
There are 2types of Clamping type floor polishing brush:
a)The traditional floor polishing brush has a short fixed pile used for driving the grinding brush at run time.
b)Central locking type polishing brush in addition to a set of short pile and a fixed center of plastic locking system. It can effectively prevent running off on the brush plate. This type is especially suitable for machines with a few brushes at the same time, It helps to align the center of the brush disc.
All detergents used by the floor scrubber are especially designed for it. Basically, it should be basic and there is a trace of the bubble (if too much foam will cause damage to the water pump) detergent. Do not use acid or corrosive detergent. More prohibit the use of flammable properties of detergent. Adjust the concentration according to the condition of the detergent. For the dust or stubborn dirt ground, Recommend to clean it before use detergent . Take longer Cleaning time, but get better effect .Should clean twice. For the first time, close the suction pump, and bring up the suction plate, pure wipe the ground. Second times, use the detergent on the ground which has been cleared, it is clear that the cleaning effect?
If the model is suitable for the working environment, most of the operation problems are easy to solve. In fact, the machines are used in the place that is not in conformity with the model. And not because of the machine itself technical problems, but the machine is not applicable to the working environment ,Therefore come problems, it is not uncommon.
The following list of possible problems in the safety and cleaning effects considered:
Check operation problem
Cleaning brush water shortage
1)Check valve (including manual valve and electric valve if open).
2)Check whether there is water in the solution tank.
3)Clean the solution tank filter (if has).
4)Check whether the water pipe connected with the cleaning brush is blocked.
Poor cleaning effect
1)Check the wear level of the cleaning brush, if necessary, replace it immediately(If the brush hair curl more than 15 mm must be replaced)
2)Use Other types of cleaning brush. We propose to use a special cleaning brush when cleaning the floor that is hard to clean
Suction disc can't completely dry floor
1) Check whether the water absorbent rubber pad is clean or the internal suction disc accumulate dirt.
2)Replace worn rubber. Adjust the angle of the rubber, adjust according to the degree of the rubber wear,so that get better cleaning effect . Rubber should be slightly lean back 5mm, the whole length should be so.
3)Check whether the water suction hose connected with the recovery tank.
4)Take off the unit and clean.
5)Replace the wear rubber.
6)Check the water pump switch is open or not.
7) Check the suction disc wheel adjustment.
Bubble too much
Whether use low foam solvent. Add a little defoaming solvent in recovery tank if necessary.
Please note that the more cleaner floor , the more foam will be. In this case it must diluted detergent before use.
The daily maintenance work is very important for special cleaning machine. This type of machine to clean with water,
Need simple daily maintenance work, or, at least for maintenance after in daily working
For example, the maintenance work needs:
1)Empty and clean the recovery tank. In the process of cleaning machine suction dirt will rapidly precipitate and emits an odor
2)Empty the solution tank. When the machine is not work every , which is more important . Because it is easy to have a viable bacteria in Stagnant water
3)Clean the suction pump filter. When there is a dirt deposited, will weaken its ability to inhale. Leading to clean with water
4)Check whether the suction plate is clean. If necessary, use faucet clean rubber and suction pump suction
5)Weekly cleaning brush and suction plate wear degree examination, such as extremely uneven ground, the pressure from will have damage lead to wear and tear on the parts. Under normal circumstances, cleaning brush need to be replaced after working 50 hours, rubber needs after 30 hours for flip or replacement
6)Check the filter regularly , mixed with a small amount of impurities, may lead to blockages in work and influence in the process of clean water
7)clean the suction hose connected to the suction plate regularly. Even if it's just part of the blockage, also will weaken the dirt suction work.
Read carefully on the machine's symbol, do not cover these symbols, if there is any damage needs to be changed immediately.
1)The machine is for the use of specially trained personnel only.
2)When using the machine, should pay attention to others, especially children's safety
3)Don't put the mixed with different kinds of detergent, lest produce harmful gas.
4)Don't be put any liquid container on the machine.
5)Machine must be synchronized complete cleaning and sucking up the ground. Any other unauthorized personnel is strictly prohibited. Wet the ground should be equipped with appropriate signs
6)For replacement parts should apply to the original manufacturer.
7)Prior to any maintenance work, must cut off the main power supply at first.
8)Don't unarmed disassembly parts requiring the use of tools.
9)Don't use faucet directly or with pressurized water and corrosive substances directly cleaning machine
10)After Every 200 hours working, the machine need to repair service center.
11)Solution tank filter to avoid fouling, don't add detergent only hours before the machine's use.
12)Use the machine, according to the instruction manual check all valves, shell cover is in place.
13)Before removal of recovery tank, make sure it has been cleared
14)Pay attention to comply with the relevant regulations when dealing with the waste
15)After the machine scrap, serious processing machines in the oil, battery and electrical components。
Please keep in mind that all components of this machine are all renewable materials.
needs and floor situations are had to deal with .Also, buy what kinds of part, working environments, machine sizes, the dirt types, working hours and quality requirements. Should consider the characteristics of the model can meet the needs of the customers, when choosing models. The higher requirements, the more frequently used, the more important t to choose professional models
1)Machine efficiency, reference machines clean area (i.e., the size of the route)
Work efficiency, possible problems and downtime. Usually by trial machine for an hour, as a standard to calculate
2)Quality of work, mainly depends on the cleaning unit ,brush pressure, brush types, brush speed,
Suction unit, and the solvent types.
3)Work effect and reliability, ensure the lifetime of the machine. For example, the types ,structure, whole frame, cleaning units, motors ,electric parts, quality and reliability of mechanical components.
4)Handling and ergonomics, affecting the use of the machine. The operation of the machine, should be convenient and easy, so that the controller in any environment, conditions have a good vision. Machine size is also very important, to ensure that the work of vision, and the operation of the machine should be easy to understand and implement
5)Safety, strictly in accordance with the relevant provisions, considering that the machine can sometimes be in dangerous working conditions, the driver will operate in a crowded area, which is particularly important. The use of the machine, according to the European regulations on electromagnetic compatibility and reduce noise;
Comply with the European construction technical specification; All visible part to comply with the relevant building regulations, will not damage to the operator and others; The machine must be specially trained personnel careful operation; To use a special detergent and avoid a mixture of different kinds of detergent; Avoid using the machine in the explosive environment. Prohibited by machine to inhale dangerous flammable liquid and powder; Finally also note, do not use machine on the steep slope.
The machine operating cost depends on the consumption of liquid detergent, Energy consumption - if electric fuel control, water consumption. In addition to harm also depends on the necessary maintenance and spare parts consumption of wear and tear, such as, brushes, pad drivers, squeegees.
What's more the machine should with all the necessary parts.
as, Can detect detergent dosage of electric valve, strengthen the absorption effect of high power motors. According to the actual need to adjust the brush pressure; The adjustment of the basic process and daily maintenance has its practical and simple; Electronic equipment installed on the machine display is simple, convenient operation, to avoid multifarious machine downtime, have very great help to reduce the maintenance cost.
To provide good service, which is very important to choose and buy the machine. Expert advice and training to the users, quality assurance, good service, high performance of spare parts, Detailed maintenance plan, high-performance machines.
浙公網(wǎng)安備 33038202002089號
友情鏈接：江西洗地機
